Overcoming Blingking on Canon Printer
It's not uncommon for owners of Canon printers when printing on strike tool with lights blinking orange and green alternately. There are several kinds of blinking on the printer Canon. But that will be discussed this time is blinking orange it turns green once.
The message that appears when this happens usually blink "waste ink tank full" or "absorbeb ink full". This happens because the waste ink reservoir management due to frequent cleaning or filling head is too full of ink so that when the ink cartridge is installed seeping out through the printhead.
Many stores or places that serve computer services pebaikan this error rates varied between 50 to 75 thousand dollars. It's just that only one or two places that do repairs completed. Most only make the process of reinstalling the EEPROM only, or better known as a flash, without bothering to shuffle through the printer.
Please note that the source of the disease in this case is blinking like a bin full of ink. To avoid leakage of ink, the sensor sends a message to the printer processor to stop working. Unfortunately sensor recognizes only the full shelter without being able to recognize it when the tub is emptied. Although already cleaned, the printer still would not work without our counter reset EEPROM through the flashing process.
Only diflash, the printer is able to work again. But do not forget, without cleaning inkwell has not lost a source of illness. Like our last thorn anesthetic injection. The pain is not felt but the thorns remain. Once biusnya lost influence, felt more pain.
So there's nothing wrong if we find such cases, ask for service personnel to clean the ink reservoirs. If you have to wait, the process did not take long.
Or if you want a little rolled up their sleeves, not hard to do it themselves. Here we discuss a step-by step.
Prepare the printer in a safe and comfortable. Give the base of unused cloth to avoid the scattered ink. Prepare equipment plus a screwdriver and tweezers or pliers to take the foam taper or use hand can also if you are not afraid to do dirty.
The first step is to open and close the lid of the printer. Open the front two screws and lift the printer casing.
PCBs in the plate off the cartridge with the opening track three screws. Unplug the pump cord ink.
Open the screws on the back of the rail under the PCB position, 2 screws on the rail cartridge, 1 on the right side and 2 on the left side. Remove the cartridge rails. The cables do not need to release much less on the type of cable PIXMA directly soldered to the PCB without the socket.
Open the screw on the pump ink, 3 in the front and 1 in the rear. Lift the pump, be careful with the remnants of ink that is not to spill.
Remove the foam impregnation of the ink reservoirs with caution. There are 2 pieces of foam and one small one. Take then cleaned with water. The most effective way is with a sponge wrung under running water faucet. After drying to dry clean.
Done cleaning foam, the raft back to the printer. Be careful not there too, especially the installation of the roller
Once assembled properly, prepare the computer and software for flashing process. There are several software for different printers, namely:
A1800 for i320
A1600/A1900 for i255, i350, i355
T5061 for ip1000
T3164 to reset the Main and Platen Waste Waste ip1500
One use of the software will cause the printer series and / or address change within the EEPROM data defects (defects) in effect at the time of the failure of the first initialization after a reset and switched on or invalid counter value.
Make sure the printer drivers already installed on your computer.
Connect the power cable and turn on the printer. Connect the usb cable. When the message "New hardware found" wait until the driver install process is complete.
General Tool Open programs in accordance with the type of printer.
Select a usb port that is used (1). Click the "Set Destination" (2). Click the "Device ID" (3) is shown the type of printer and serial number. Click "EEPROM dump" (4). Click the "EEPROM Information" (5) will display the printer information including the date of production and the date reset. When the printer has been reset, the two are not the same date. The failure of flashing process or too often because diflash not cleaned the tub will cause the information and cause chaos in the system work processes go wrong printer.
Finally click on "Test pattern" (6). Do not forget to check back in the cleaning and the clear box eeprom. Printer will do headcelaning and testprint. Turn off the printer and switch it on again.
If all processes are running correctly, your printer will return to normal.
In addition to reset, General Tool is also able to perform tests such as "Heat Run" to check the printhead heater. Endurance Cleaning to clean the printhead further. Wipping Endurance Cap rubber test printhead cleaning. Ink Consumption to clean the capillary in the printhead for each color (Cyan, Magenta, Yellow and Black)
General Tool software can be downloaded at http://www.printersiam.com or http://www.it0577.com/yezmao. Zip file in a form that is not too large, 9.9 MB for i255 and 7.8 MB for the ip1000.
Okay, boss. Happy hunting and trying to dismantle the software being dismantled while enjoying the splashes of ink. "It's not creative dirty ...."